MULTIPLE CHOICE: Choose the most correct answer per question. 1. When practicing horizontal V-groove welds (2G) using stringer beads, the work angle should be a) 5 degrees b) 45 degrees c) 60 degrees d) adjusted as needed to ensure tie-in 2. The place in a welded joint where the two components are closest to each other is the a) groove radius b) weld toe c) bevel depth d) joint root 3. When using weave beads on flat V-groove welds (1G) keep the electrode at a 10-to 15-degree drag angle and a work angle of a) 0 degrees b) 45 degrees c) 60 degrees d) 75 degrees 4. If a groove for a weld goes through the entire base metal thickness, it makes a(n) a) complete joint penetration (CJP) weld b) subsurface joint penetration (SJP) weld c) partial joint penetration (PJP)weld d) axial joint penetration (AJP)weld 5. Before practicing a V-groove weld in the overhead position (4G), you should __ . a) change to constant voltage DC b) build a practice pad with stringer beads c) increase the amperage to the top of the correct range d) change to E6010 electrodes Weish with Backing (Plate) NOTE: The exam is not elighte for a credental. NCCER. Permasion is granted to reproduce this pags provided that copies are for local use only and that each topy contains this notice. Page 1 of 2

Question

MULTIPLE CHOICE: Choose the most correct answer per question. 1. When practicing horizontal V-groove welds (2G) using stringer beads, the work angle should be a) 5 degrees b) 45 degrees c) 60 degrees d) adjusted as needed to ensure tie-in 2. The place in a welded joint where the two components are closest to each other is the a) groove radius b) weld toe c) bevel depth d) joint root 3. When using weave beads on flat V-groove welds (1G) keep the electrode at a 10-to 15-degree drag angle and a work angle of a) 0 degrees b) 45 degrees c) 60 degrees d) 75 degrees 4. If a groove for a weld goes through the entire base metal thickness, it makes a(n) a) complete joint penetration (CJP) weld b) subsurface joint penetration (SJP) weld c) partial joint penetration (PJP)weld d) axial joint penetration (AJP)weld 5. Before practicing a V-groove weld in the overhead position (4G), you should __ . a) change to constant voltage DC b) build a practice pad with stringer beads c) increase the amperage to the top of the correct range d) change to E6010 electrodes Weish with Backing (Plate) NOTE: The exam is not elighte for a credental. NCCER. Permasion is granted to reproduce this pags provided that copies are for local use only and that each topy contains this notice. Page 1 of 2

Answer 1

1. When practicing horizontal V-groove welds (2G) using stringer beads, the work angle should be__a) 5 degreesb) 45 degreesc) 60 degreesd) adjusted as needed to ensure tie-in2. The place in a welded joint where the two components are closest to each other is the __a) groove radiusb) weld toec) bevel depthd) joint root3. When using weave beads on flat V-groove welds

keep the electrode at a 10-to 15-degreedrag angle and a work angle of __a) 0 degreesb) 45 degreesc) 60 degreesd) 75 degrees4. If a groove for a weld goes through the entire base metal thickness, it makes a(n) __a) complete joint penetration (CJP) weldb) subsurface joint penetration (SJP) weldc) partial joint penetration (PJP)weldd) axial joint penetration (AJP)weld5. Before practicing a

weld in the overhead position (4G), you should __a) change to constant voltage DCb) build a practice pad with stringer beadsc) increase the amperage to the top of the correct ranged) change to E6010 electrodes

Problemas

Roztwór

Respuesta