Pagina de inicio
/
Tecnología
/
GMET Computer Company Hardware Installation Instructions: CPU memory modules, & video card In order to avoid an electrical charge, place the motherboard on a rubberized pad on a wooden table Check the pins of the Central Processing Unit (CPU) to be sure they are not bent.Match the pins to the Zero Insertion Force socket by orienting the marked pin with a notch in the socket. The CPU should slide into place without force The processor may already have the heat sink and fan attached to it, so attach both parts simultaneously. Press down on the lever to lock it in place Next, the memory sticks and video card are installed. When inserting the memory modules, use slots one and two on the motherboard. Be sure to pick up the memory sticks by the edges Press the sticks into the slots until the ejector clips lock. If the memory modules are not locked into place, the motherboard will produce an audible beep when the system is turned on. Next, the video card (AGP type)is placed in the expansion slot, which is usually brown and the uppermost slot on the motherboard. Gently work the video card into place Last, test the assembly by plugging the unit into the power supply Also attach it to a test monitor to be sure that there is power to the system and a blowing fan. The video screen should display the Basic Input/Output System (BIOS). This shows that the CPU installation was successful and the CPU, memory modules.and video card are recognized You work at GMET Computer Company. According to the instructions shown, what is most likely the problem if the CPU does not slide into place without using force? A. The heat sink and fan were not attached to it simultaneously B. The lever was not pressed down to lock the CPU in place. C The marked pin was not bent to fit the notch in the Zero Insertion Force socket. D. The motherboard is defective E The pins are not matched to the Zero Insertion Force socket.

Problemas

GMET Computer Company Hardware Installation Instructions: CPU memory modules, & video card In order to avoid an electrical charge, place the motherboard on a rubberized pad on a wooden table Check the pins of the Central Processing Unit (CPU) to be sure they are not bent.Match the pins to the Zero Insertion Force socket by orienting the marked pin with a notch in the socket. The CPU should slide into place without force The processor may already have the heat sink and fan attached to it, so attach both parts simultaneously. Press down on the lever to lock it in place Next, the memory sticks and video card are installed. When inserting the memory modules, use slots one and two on the motherboard. Be sure to pick up the memory sticks by the edges Press the sticks into the slots until the ejector clips lock. If the memory modules are not locked into place, the motherboard will produce an audible beep when the system is turned on. Next, the video card (AGP type)is placed in the expansion slot, which is usually brown and the uppermost slot on the motherboard. Gently work the video card into place Last, test the assembly by plugging the unit into the power supply Also attach it to a test monitor to be sure that there is power to the system and a blowing fan. The video screen should display the Basic Input/Output System (BIOS). This shows that the CPU installation was successful and the CPU, memory modules.and video card are recognized You work at GMET Computer Company. According to the instructions shown, what is most likely the problem if the CPU does not slide into place without using force? A. The heat sink and fan were not attached to it simultaneously B. The lever was not pressed down to lock the CPU in place. C The marked pin was not bent to fit the notch in the Zero Insertion Force socket. D. The motherboard is defective E The pins are not matched to the Zero Insertion Force socket.

GMET Computer Company Hardware Installation Instructions: CPU memory modules, & video card In order to avoid an electrical charge, place the motherboard on a rubberized pad on a wooden table Check the pins of the Central Processing Unit (CPU) to be sure they are not bent.Match the pins to the Zero Insertion Force socket by orienting the marked pin with a notch in the socket. The CPU should slide into place without force The processor may already have the heat sink and fan attached to it, so attach both parts simultaneously. Press down on the lever to lock it in place Next, the memory sticks and video card are installed. When inserting the memory modules, use slots one and two on the motherboard. Be sure to pick up the memory sticks by the edges Press the sticks into the slots until the ejector clips lock. If the memory modules are not locked into place, the motherboard will produce an audible beep when the system is turned on. Next, the video card (AGP type)is placed in the expansion slot, which is usually brown and the uppermost slot on the motherboard. Gently work the video card into place Last, test the assembly by plugging the unit into the power supply Also attach it to a test monitor to be sure that there is power to the system and a blowing fan. The video screen should display the Basic Input/Output System (BIOS). This shows that the CPU installation was successful and the CPU, memory modules.and video card are recognized You work at GMET Computer Company. According to the instructions shown, what is most likely the problem if the CPU does not slide into place without using force? A. The heat sink and fan were not attached to it simultaneously B. The lever was not pressed down to lock the CPU in place. C The marked pin was not bent to fit the notch in the Zero Insertion Force socket. D. The motherboard is defective E The pins are not matched to the Zero Insertion Force socket.

Solución

avatar
Miguelprofessionell · Tutor durante 6 años
expert verifiedVerificación de expertos
4.1 (319 votos)

Responder

'E'

Explicar

## Step 1<br />The problem is about the installation of a CPU (Central Processing Unit) in a computer. The CPU is a crucial component of a computer that performs most of the processing. The instructions provided in the problem guide the installation process of the CPU, memory modules, and video card.<br /><br />## Step 2<br />The problem states that the CPU does not slide into place without using force. This indicates that there is an issue with the installation process.<br /><br />## Step 3<br />Looking at the options provided, we need to identify the most likely cause of this problem. The options are:<br />A. The heat sink and fan were not attached to it simultaneously.<br />B. The lever was not pressed down to lock the CPU in place.<br />C. The marked pin was not bent to fit the notch in the Zero Insertion Force socket.<br />D. The motherboard is defective.<br />E. The pins are not matched to the Zero Insertion Force socket.<br /><br />## Step 4<br />Option A is not likely to be the cause of the problem because the heat sink and fan are not directly related to the CPU's installation.<br /><br />## Step 5<br />Option B is not likely to be the cause of the problem because the lever is used to lock the CPU in place, not to facilitate its installation.<br /><br />## Step 6<br />Option C is not likely to be the cause of the problem because the marked pin is supposed to fit into the notch in the Zero Insertion Force socket.<br /><br />## Step 7<br />Option D is not likely to be the cause of the problem because the motherboard is not defective.<br /><br />## Step 8<br />Option E is the most likely cause of the problem. If the pins are not matched to the Zero Insertion Force socket, the CPU will not slide into place without using force.
Haz clic para calificar: